High Frequency Transformer LED Lighting - Step-Up Electronic Transformer from China Suppliers and Factory
Home appliance power supply, industrial and communication equipment power supply, printer, copier power supply and emerging medical equipment, small power supply, network communication power supply, 5G network communication products, bathroom products, refrigerators, washing machines and other home appliances.
The length and width can be 4mm, the duty cycle is small, can be customized according to specifications, and the power can more than 60W.
Key Point 1 — Winding
A. Determine the parameters of BOBBIN.
B. The principle for all wire wrapping is to ensure flatness and non-overlapping.
C. For single-group wiring, a single-colored wire is sufficient. For double-group wiring, use double-colored wires or open wires immersed in tin to distinguish the pins, to avoid wiring errors.
D. The crossing line must be isolated with tape.
1. The sparse winding is completely evenly spaced.
2. The closely wound wires are evenly and tightly arranged.
3. Both sides of the coil should maintain a sufficient safety distance A and B from the edges of the winding slot.
4. The length of the sleeve must be sufficient, with one end extending into the safety tape of the winding tube and the other end extending beyond the upper edge of the BOBBIN, but must not be close to the PIN.
5. The outermost tape is cut on the core assembly surface, and the cut area must be covered by the core.
6. The edge of the tape should be flush with the winding groove, and the tape should not be skewed, folded back, or damaged.
7. Tape must be applied under the crossover wire to maintain insulation between the crossover wire and the underlying coil.
Key Point 2 — Thread Winding
Vertical BOBBIN:
Thick wire (above 0.8φ): wrap once. Fine wire (0.2–0.8φ): wrap 1.5 times. Extremely thin wire (below 0.2φ): wrap 2–3 times.
Principle: The wire should be wound as tightly as possible without exceeding the protruding points.
Horizontal BOBBIN: Wrap approximately 2–3 turns, do not press the sparse winding down to the bottom to avoid burning the BOBBIN during soldering.
Note: If the product has a width limitation and the specifications are tight, the wire-wrapping must be pressed down as much as possible.
Key Point 3 — Casing
General rules for the location of casing:
A. Externally: The shorter the distance between the end of the sleeve and the PIN, the better. However, it is absolutely forbidden to wrap the sleeve around the PIN.
B. Internally: a seamless wall fit, flush with the BOBBIN for approximately 1/2L in length.
The width and material of margin tape cannot be arbitrarily changed, as they are subject to safety regulations.
The width of the tape for the false wall should generally be equal to the height of the winding coil to prevent copper wires from overlapping on the false wall during winding.
Key Point 4 — Copper Sheet Winding
A. A circle of unconnected leads, with no short circuit between the ends, and separated by insulating material.
B. For connecting wires in a circle, the width of the tape must be greater than that of the copper sheet.
C. Two leads of copper sheets with more than one turn.
D. Copper sheet of intermediate drawn type, with three leads.
Key Point 5 — Cable Management
1) Vertical cable management standard:
Both thin and thick wires need to be neatly wound for more than one full turn, with the winding position located at 2/3 of the height between the base and the boss.
The length of the wire end must not exceed half the distance between two adjacent feet, and the maximum length must not exceed 1mm.
Multiple sets of wires are wound together and organized. The thin wires should be placed on the top layer.
2) Horizontal cable management standard:
The thread should be evenly distributed on the foot, with the thread end extending at least half of the length of the thread foot.
The thread should be wound spirally upwards from the heel and should cover at least one full circle.
The length of the wire end must not exceed half the distance between two adjacent pins, and the maximum length must not exceed 1mm.
Key Point 6 — Soldering
1) After soldering, the PIN legs should be flat and smooth, without any foreign objects adhering to them.
2) The thread end should not be higher than the bump.
3) After soldering, the BOBBIN should be intact, with no damage or short pins.
4) There is minimal residue of soldering flux, with no tin staining or short circuits.
5) The adhesive tape shows no damage.
6) The solder should cover at least one full circle.
7) After soldering, there should be no lateral solder spikes.
Key Point 7 — Combination / Assembly
1) The iron core assembly surface should be flat and free from any tilt.
2) The bobbin, core, and wiring pins should be kept clean and free from any impurities or adhesive.
3) Identify the direction in which the CORE with GAP should be placed.
4) The maximum skew of CORE of EE, EI, and UU types must not exceed 0.5mm or 1/10 of the CORE width.
-
QWhat are the main application areas of high-frequency transformers?High-frequency transformers are widely used in home appliance power supplies (refrigerators, washing machines, bathroom products), industrial and communication equipment power supplies, printer and copier power supplies, medical equipment, 5G network communication products, and small network communication power supplies.
-
QWhat are the key specifications of this high-frequency transformer?The transformer features a compact design with a length and width of 4mm, a small duty cycle, and a power output exceeding 60W. It can be fully customized according to customer specifications to meet various application requirements.
-
QWhat winding principles must be followed during the manufacturing process?The core winding principles include ensuring flatness and non-overlapping of wires, using color-coded wires for multi-group wiring to avoid errors, isolating crossing lines with tape, maintaining sufficient safety distances from winding slot edges, and applying tape under crossover wires to ensure insulation.
-
QWhat are the soldering quality requirements for high-frequency transformers?After soldering, the PIN legs must be flat and smooth with no foreign objects. The thread end should not exceed the bump height. The BOBBIN must remain intact with no damage or short pins. Minimal soldering flux residue is required, with no tin staining, short circuits, tape damage, or lateral solder spikes. The solder must cover at least one full circle.
-
QCan the high-frequency transformer be customized to specific dimensions and power requirements?Yes, the transformer can be customized according to customer specifications. The compact 4mm form factor supports flexible design, and the power output can exceed 60W, making it suitable for a wide range of applications from small consumer electronics to industrial and communication equipment.
-
QWhat are the assembly and core placement requirements for high-frequency transformers?The iron core assembly surface must be flat and free from any tilt. The bobbin, core, and wiring pins must be kept clean and free from impurities or adhesive. The correct direction for placing the CORE with GAP must be identified. For EE, EI, and UU type cores, the maximum allowable skew must not exceed 0.5mm or 1/10 of the CORE width.


















